For Your Own Peace of Mind - Organize!

 

As my previous post said I'm packing to move. The deadline is fast approaching and of course I'm scrambling now since before this I had 'plenty of time'. I no longer have 'plenty of time'.

I'm going to use this post as a heartfelt plea for you to go through your hobby/office spaces. Please declutter and throw out/donate/sell what you're not going to use. Look, actually look, at what you have and be brutally practical. Take what's left and put it into storage containers, then put those on shelves. It's a lot of work and it may not seem necessary if you're in your forever home or don't plan on moving.

But sometimes you don't get the luxury of planning on moving. Sometimes your forever home turns out not to be your forever home. And in general we collect and pile up a lot of crap.

I was somewhat lucky in that I started organizing things into plastic storage bins a while ago but never really finished. I'm paying for that now in some respects and in others not so much. I can use a lot of the 'unorganized' things and use them to fill space where the containers don't fit the boxes. That helps greatly in the short term, it isn't so great in the long term.

I'm not saying you can't keep things 'just in case'. I've got a lot of things like that for scratch building and they pack up just fine. When they're unpacked they're going into, you guessed it, plastic storage bins. I've also found a lot of things that I kept because it was more convenient than throwing them out. That's no longer the case. I don't need them and see no use for them in the near to moderate future. So they go.

When you're in one place for a long time this happens. It's easier to leave things out because you're using them than it is to go through and put them away. Piles occur. There's no judgement here. There can't be based on my own situation. But I'm saying that organization will save you a lot in the long run.

I'm a big fan of plastic bins over cardboard when possible. Get ones with tops. I use a lot of the dollar store ($1.25 store?) plastic shoeboxes and their smaller containers with handy flap lids. Those two sizes are mostly what I use since I can't make them too heavy for metal miniatures and the supplies fit mostly very well into the smaller ones. I'm also a huge fan of the 16 x 16 scrapbook paper holders from the craft store since they hold mini paint bottles well. I have a cart that holds six of those. I'm going to need another cart. But when I put the paint away it's put away.

In general it's a lot easier to find stuff if you've put like with like. All the sandpaper? In a plastic paper holder with a sliding lock. All the Dremel accessories? In a container. All the bases? In a container. It's work up front but if you look at it, really look at it, it's a one time pain. Then it saves you time when you're looking for where you put whatever later.

I also have storage cubes with doors. I lucked out getting those because they were discontinued. They fit perfectly into my current space and should fit well into my new space with some planning. Right now they're handy to where I paint so I can keep things I use a lot in there. In plastic storage bins or loose-ish in other kinds of containers. I use a pill bottle and a pilsner glass for the second rate and terrain paint brushes. They're contained.

I'd have a lot more trouble if I hadn't done this up front. Even with doing a partial organization it's saved me a lot of time and things are already together. When a box has 'bases' written on it I know all the bases are in there when it comes time to unpack. When a box has 'air' written on it I know it's everything I need for the air compressor. There will be other things in those boxes but I know what the important things are.

Another thing I found from all this is just how much I have of particular kinds of items. Between you and me I have too many of some. I know I can clear one of those when I get settled. The other will take more work and planning. But until it was all gathered up I didn't know the extent of what I had. Having it scattered put it out of mind. Having it put in one place lost me that luxury.

So just how well organized will the new space be? I'd like to think it's going to be decently organized. What's not in plastic containers will get there. The things that can be reduced will be. I will have more storage space so more things will be visible for me to use. I'll even label the containers if I get all kinds of ambitious. Those are all future considerations. Right now it's a matter of a rough organization of at least getting things into the boxes that will go into the same room.

I'm lucky in that I'll have more rooms for things now. With my hobbies I outgrew my two bedroom apartment resulting in a dense accumulation that was difficult to use. I worked hard to use every possible bit of storage space and I think I did well. The problem with that was getting to most things. I also had things on the shelves that I wasn't going to use but had the space to put them. That happens. That's going to happen again. By having more rooms and separating two big space hogging hobbies I'll have actual room to work. That's a luxury I haven't had for well over a decade.

I'll end this as I started, begging you to take the time to organize what you have. Plastic works better than cardboard in my opinion because if something bad happens that involves water your stuff has a much better chance of coming through undamaged or at least minimally damaged. Wipe it off and put it back. Cardboard, not so much. There's enough variety of sizes and shapes of plastic containers that you can find what you need or at least what will work well enough. You don't have to do it all at once. But please, please, please do it.

So, Um, What's Going On?

If you follow me on Twitter (hi!) or are a Facebook friend (hi!) then you know the real life stuff that's going on with me. If you don't know me from either of those places then all you need to know is that real life stuff is going on with me.

I've been quiet here because I haven't felt I would have much to say about gaming, which is the primary focus on this blog lately.

The game hasn't been going well. I think it's a combination of an ill-matched group, an ill-matched GM and group, and moving the game online. The only thing out of those three that could possibly be changed is the online part but it wouldn't fix the other two.

The ill-matched group has some odd dynamics since it's morphed so many times. There's now a husband and wife team, their friend (at least I think he's their friend, he may be the friend of the guy who abruptly left), and one person who's stuck through from the beginning. Their characters haven't meshed into a party - they're four people hanging out and doing stuff but they're not a PARTY in that they're forming interpersonal relationships. Not the players, the characters. Which is also the players but not really.

Only one player gave me enough backstory to work any of it into the game. The others gave me a little along the lines of "I'm trying to find my father but not really" and "I want to learn more magic before I go home". That's not enough for me to find a way to work them into a story. It's separate people with separate goals.

Here's where I get to vent a little. I want them to enjoy the game. I want them to try to put together larger pictures from what they gather as they adventure. I want everyone to have fun. But this group just can't see clues. I wondered if I was being too subtle so I literally attacked them with NPCs that should have spurred them into trying to figure out why they were being followed. Nope. As soon as the encounter was over they barely talked about it even though the NPCs got away. When they were attacked again, same result. How much more obvious do I have to be that there's something going on?

This is why I think the group and I aren't a match. My GM style doesn't mesh with their play style. That's not saying either one is bad. That's saying they don't work well as a game. It means no one is having as much fun as they could and should.

This leads into why my short lived "How I Roll" suddenly ended. I couldn't come up with enough things to continue it. That was an offshoot of me doing game prep and how things worked in my game. Since I no longer get any pleasure from game prep and the things that go on in my game aren't worth mentioning it ended that set of posts. Maybe in the future I'll pick it up again, maybe not. I don't know how much people liked it.

Ending a game is a difficult decision. I've done it in the past when I knew I wasn't giving them the game they deserved. I never heard from any of the players again after it ended so I know I made the right choice. That hurt, by the way. No one even thanked me for that game or the one before (most of the group was from the previous game that ended due to players moving away).

Ending a game in these times is an even more difficult decision. Everyone needs an escape. Gaming is a wonderful escape. But when it becomes something I dread rather than look forward to with anticipation then I know there's problems. Big problems.

I've tried to fix it by asking players what they wanted out of the game and got non-committal answers that didn't help me at all. They were along the lines of what I already said. Mostly they want to play and this is a game they have. It's not that they want to play MY game. It's that they want to play A game. At least that's the feeling I'm getting.

I could run a series of loosely collected pre-generated adventures to keep the game going. No one seems to be looking for a long term story arc. But that would put me in the position of reading Powerpoint slides. That's not what I want to do. Sure, it's easy to prep. Print off a map, print off the adventure, run them through it. I have plenty of those that I use for inspiration. But if that's all they want then there's a lot of other GMs to do that. I want to get engrossed in the story they weave. I'm there to support that and they're not storytellers.

This is me talking myself into ending the game, if you couldn't tell.

I am looking at Fantasy Grounds and running regular one shot adventures for people who just want to show up, grab a pre-generated character, and play for a few hours with no long term consequences. There's so much league play these days where every result is a permanent result I want to think that there's people out there who want carefree play too.

That would let me have some fun with adventures and also play with no long term consequences. Sure it might seem little different than what I said I didn't like about my current game but it's different. It's meant to last a few hours then end forever. One shots as opposed to a string of encounters.

I have a few days left before I need to make a decision. Wednesday before the game is my traditional time to contact the group and remind them we're playing. That's a way for people to say if they can't play as well. I canceled the last game due to the stuff from the first paragraph and one player would have had to cancel anyway due to their real life stuff. So we're already several weeks out from the last session.

What will I do for a creative outlet?

I can work on learning Fantasy Grounds since I like learning things and seeing how to make games there.

I can work on my hobbies.

But I know that my full creativity is blocked at the moment. It's been blocked for a while. The world changed. We're all excused for having bad mental reactions to what's going on. For me it means that I don't think I can run games right now. I can't give myself over to the fun of figuring out imaginary challenges to overcome when we're all dealing with real life challenges. That's not fun.

Anyway. I wanted to let you know that I've been feeling guilty about not posting an update. I'm still around and I hope to be posting about other things that I can do. They probably won't involve gaming as much. I have many other hobbies and interests that I enjoy sharing. Maybe switching to those will put me in a better place to be creative in general.

A Very Productive Weekend

It wasn't as productive as I hoped but I'm very happy with what I got done.

First off - basing sand for miniatures. Long, long ago I bought a pound of something called 'decor sand' at a garden store. It was sand with a mixed grade of granules so there was some really nice variety in there. I used it on my minis to much success. But then I ran out. I couldn't find anything local and made a make-do mix of sand and talus.

When I went back to the Midwest for a friend's wedding a few years ago I went back to the store with the intention of bringing home several pounds of it. Sadly they no longer carried it.

I continued to limp along until I saw one of DM Scotty's videos where he recommends construction sand for that exact thing - far more irregular mix of sand for basing. I was happy!

Construction sand only comes in forty pound tubes. That's a lot of sand. I did get a broken one at a seventy percent discount and it sat in the trunk of my car for months. Mostly because I literally had no way to carry it to the apartment. It was very precariously bagged.

Finally this weekend I used the sifter I printed (I checked the manufacturer's description and found that the largest grit was far larger than I liked for minis and printed a sieve of appropriate size) and separated all the sand. I had to do it over two days because I ran out of storage containers and because it was getting dark on Saturday.

On the left, basing sand. On the right, rocks. Underneath, sixteen inch paving stones to go under the upgraded 3D printers and a broken cut-off wheel from the next listed project.

Yeah. I'm going to have to find a home for a lot of this sand. Because I have way too much of it even with the number of minis I need to paint. I'm still debating about that. There were a surprisingly small amount of rocks in the mix which makes me happy. It still leaves a lot of sand.

Next up was shelf support. The shelves I put in the craft/sewing/office room didn't have enough dividers. I used an extra set to add a level above what the intended size was so I really can't blame them. The top shelves were always intended to hold army transports both empty and full so that was going to need to be fixed.

I bought a four inch diameter pipe from Home Depot and needed to cut it down to the correct size. That pipe sat in the room for months. The shelves sagged more and more. This weekend it was remedied. The pipe was cut (combination of Dremel and hand saw) and the cut edge smoothed and chamfered. With only moderate profanity it was wedged into place and the shelving unit is now complete.

Before:

After:

Scary sag gone. I made sure the size would be enough to span all of the shelves and support them equally. No more worries about the top layer collapsing and the shelves breaking, much less what would happen to what was on them.

Next up was 3D printer related. One of the fans died and the replacement fan I had didn't have the correct connector. Correct fan, not correct connector. The solution is to solder the new fan onto the old cable. It's a known solution and not something that bothers most people. You can buy fans from 3D printer stores with the correct connector in place but I got mine from Amazon. I'd been putting off the project because I just didn't want to do it. That and my soldering skills are somewhat rusty.

Solder and heat shrink tube later and I have the new fan ready to be put into the printer. This is the one thing I didn't get done that I had planned. I was going to reassemble the printer and yes, I could have done it instead of writing this very long blog post. But I know my state of mind and would rather not have tried to reassemble it tonight. I know my limits. I'll do it this week after work one day.

Those are various and sundry 18mm miniatures I've printed along with a very handy nipper for cutting filament at the right angle to load into the printer. I printed that too - except the razor blade inside. It's also darn good at nipping incautious fingers.

Last but not least was something for me to do while I had all the stuff out to cut the support pipe. A future as of yet not disclosed project needs a rubber squeegee. It needs a small rubber squeegee. Shopping for the correct kind of rubber squeegee (I like the word 'squeegee' it seems) had me asking if I was in the wrong line of work.

Ingenuity to the rescue.

This is 3 squeegees cut down from a dollar store bathroom shower squeegee. They will work exactly the same and cost significantly less. Even better is that I can replace them very quickly.

So that was my productive weekend. I also made a trip to the not-so-local but much friendlier game store to buy the new Chessex dice that were released last week. As I warned them I ended up not buying two of the styles because they weren't attractive enough for me. These dice have swirls of color and it's very subjective. I did get two sets of another style (one to leave as-is for the collection, one to repaint the numbers a more pleasing color) and two sets from the case. One set is trade/sale fodder, the other is a nicer version of one I already have.

It might not sound like much but I did more this weekend than I've done in a very long time. I even spent a little time on the stationary bike in the apartment complex fitness room to try to make my knee feel better after standing at the trunk of my car sifting sand for far too long. It worked, along with the heating pad after.

I'm very proud of what I accomplished and the tasks I finished. I didn't just do things - I finished them. All the sand is sifted and my car trunk has been emptied. The support piece has been properly cut and finished then wedged into the shelves. Actually finishing tasks is something I'm not great at  so doing so many of them in one block of time is something I'm going to put in the win column.

And during all that I had an idea for the blog to make more content that wasn't 3D printer related. I'll have to polish up the idea and see how it flies. Stay tuned. Better yet, follow.

All Right Then

Airbrush

I have the compressor, the moisture trap/pressure regulator, the AIR HOSE, and all the air brushes where I can find them. The compressor et al is also set up where I think it's going to be when I'm using it.

The space for the booth has a piece of foamcore on it as a base for the photo tent/spray booth when it arrives. The turntable for inside the booth is sitting in a box but I can find it easily enough.

I haven't done any airbrushing because:

1 - It's been too freaking cold.
2 - Housework was needed.
3 - 3D printing.

That will change this week since the temperature is going up and the housework is getting done. About the 3D printing...

3D Printing

I was completely sick of printing grey and printing dungeon pieces. Printing grey dungeon pieces was excruciating. Therefore I took the holiday to print some stuff that wasn't grey and wasn't dungeon pieces.

I properly labeled all the test prints (low poly cats) with the brand and color of each one. I have the start of a filament cat army on the windowsill.

I also printed up useful stuff like a grip for painting miniatures, a clipper for filament (it has to be cut at an angle to be loaded), and a new case for the Raspberry Pi media server. I printed in colors! Pretty, pretty colors.

I also put up the last long shelf on the adjustable spacers and filled it with .. filament! That got the worst of it out of double rows under the printers. I also lowered the short shelf one notch so it fits all the types of boxes I have. That helps. A little.

3D Printer Repair

Absolutely nothing was done on this since the board is still in transit. It got to spend new year's eve in Germany but now it's on it's way here. It's still showing tomorrow as the delivery date but we'll see if that happens.

Since the order is a decent amount I need to sign for it. I certainly hope it shows up early because I was kind of planning on going to the post office and to the craft store after work. But if I'm waiting on the delivery that gets postponed.

Once the board is here I can restart the upgrade process and hopefully have it running by the weekend. That will be more grey dungeon pieces being printed but for a shorter period of time. Win some, lose some.

Convention

I'm still on the fence here. A big incentive for me is gone since there won't be a Chessex dice booth there. High cost and low profit were the owner's reasons for not showing up and those are perfectly valid. But I have a long shopping list and now I need to think about why I would go besides running my games.

BTW - the vendor list is currently almost empty. As in most of the spaces are showing as Available. If they haven't updated the website that's not a good sign. If that's true it's not a good sign.

My events are still showing as free even though it was supposed to be fixed a month ago. Their dashboard shows them at the correct price, the event ticket buying site shows them as free. I'm letting them work it out. Their systems are not my concern.

I'm giving it a few weeks to see how sales go. If it gets within a couple of weeks of the convention and there's very low or no ticket sales then I'm going to cancel. I know, I know. I committed to running the games. But if there's no one choosing to sign up then I won't be running games. I'll be sitting next to a table being bored. And having to pay for the privilege since I don't know if they reimburse for events that had no players. Actually I don't know their full badge reimbursement policy - commit to run the games or actually have enough players?

Housework

We're not going there.

The Doorstop and The Dungeon

My original 3D printer is still a doorstop. The controller board is bad. I'm in communication with the manufacturer since the printer itself is out of warranty but the board failed during the upgrade. I'd like them to cover at least some of the cost of replacement if they won't cover the whole cost. We'll see  how it plays out.

The other printer has been chugging along just fine. I had planned on twice the output because I'd have twice the number of printers but that's life. I'm running it almost 24/7 and it hasn't complained.

Slowly but surely I'm getting the pieces I need for my new modular dungeon. They're all printed in grey so even if I can't paint them in time they won't look that bad on the table. I'd like to paint them if possible. I even ordered a big bottle of the primer I want to use with the airbrush when I ordered some other things during their pre-holiday sale. That bottle should easily cover the entire dungeon and then some.

I also set up the new print server for the new printer. I finally printed a case for it that attaches to the frame. My previous one was just kind of sitting on the table and I think I broke the power connection because it wasn't secure. I have to exchange the memory card and I think I'll give this a try as-is because the new case is really steady on the frame so the power cable won't move around much.

I haven't set up the cameras yet because I'm waiting for both printers to be in place so I can get it all in order. I have the lamps I wanted so there could be enough light for good time lapse videos and I think I know what camera stands I'll be printing. I may print out a sample of that to see if it needs adjusting or if it will work as designed. I also have to make sure that I have the proper length cables for them. So much to set up but then it's done.

I ordered spare parts for the printers and will be ordering more from the manufacturer when I get my board. I have to pay for the overseas postage anyway (unless they cover it for me, which would be acceptable) and the things I added didn't increase the cost. They're parts I may never need but if I do I can be up and running again soon. The ones from Amazon will be here in a few days. All this means is that I need a box I can put on the shelf under the printer.

The dungeon itself is looking quite good. At least the pieces are. I haven't tried to assemble any of it yet. Honestly I've been working on getting enough of them printed. 3D printing takes time. Just to print nine of the corner pieces takes 37 1/2 hours. Nine of the single walls take around 25 hours. Note that these are attached to floor tiles so that adds time. Printing nine floor tiles takes 12 hours. It all adds up.

Mind you I'm doing different levels of the pieces at different layer heights. The stuff that doesn't matter as much - the things that don't have a top surface - I'm printing at the thickest layers the printer nozzle will handle. But doing that on the flat, textured layers means they look terrible. So I change those to be very thin layers. Thinner layers means longer prints. I weighed it out and I'd rather spend the time up front and have pieces I like rather than go faster and be unhappy with how they look.

I'll do a post just on the dungeon setup itself when there's more to talk about. Right now it's all about printing the pieces that go into it. I may do the math at the end for how much time and how much filament went into making the pieces since that's kind of interesting.

There's been some discussion on how 3D printed dungeons compare to Hirst Arts dungeons in terms of time and money. It's an interesting discussion. 3D printing is 'set and forget' while Hirst is a lot of steps. Having done both I think I might try to compare them and see what differences there are for those considering which way to go. I don't know if there will be a clear winner or not. I would surprised if there was. The Hirst vs Dwarven Forge ended up with "both have advantages and disadvantages" after it was all said and done.

I'm Back!

Well. Let's see how long it lasts but for now I'm back. I took a hiatus while dealing with life issues. I still have life issues (and I'm not naming names but you should know who you are) but I'm also getting some stuff done so I might as well blog about it.

You won't hear about the life issues unless they DIRECTLY relate to my hobby stuff. And by 'directly' I mean intertwined or in some way integral to the post in question. I purged my blog of the personal posts when I moved it from my own site and I'm not interested in putting my private life on display. 'Nuff said about that.

I've moved into 3D printing a lot of stuff so be prepared to see that more than hand crafted things. Personally I think the market is glutted with the big name crafters so I'm not too worried I'm going to prevent people from learning anything new. If I do have tutorials they'll be hosted elsewhere and I'll link to them.

I do plan on going back and fixing all the broken picture links. They will either be the original pictures (when possible) or new ones as needed. Blogs about mini painting aren't very good without pictures. That's high on the priority list even if it is seriously tedious.

Unless there's interest I'm not going to go into the process of 3D printing. Maybe I'll make some kind of sticky post if this allows for it so the basics can be there for anyone to read. This isn't a blog about 3D printing. It's about miniatures, terrain, and gaming. 3D printing is a tool.

After I get pictures back in place I want to get current with what I'm doing. I have a lot of things backed up and haven't been doing much hobby work for far too long. That happened because reasons. I still have reasons not to do it. I have reasons to do it. But I'm doing enough that it currently makes sense to start blogging again.

Now about that 3D printing thing. I will be showing non-gaming things that I print if I find there's a reason for doing so. I will mark the posts as such for those who want to skip them.

But hey. I'm back!

Busy, busy, busy

Setting goals really makes things annoying.  Once those goals get written down somewhere then there's some pressure to actually get things done.  And when you write them on a public forum (err, or blog) then there's even more pressure.  But then again, I am getting things done.  So maybe it's not all bad?

My Crusader army is two steps closer to being complete.  The bases have their rubble painted up and the bases are sealed.  Last two steps - adding the snow and then the final coat of varnish to keep everything in place.  I didn't make my January goal of getting them completed but they were painted by the end of the month.  That's something, right?

I've been working diligently on my long overdue trade pieces.  Those are the Hirst Arts arena terrain pieces I've mentioned a couple of times and shown in very bad pictures.  I've got a lot more of them painted and a goodly number waiting for paint.  And then there's the ones in various states of construction.

I'm going to digress onto construction here for a moment.  Most of these pieces were made prior to my decision to slow the heck down and not try to make things as fast as possible.  So they're not quite as neatly constructed as I would have liked.  A pillar set was so misaligned that I just put it aside and started assembling a new one.  I can use the old one myself but not as a piece for someone else.  Luckily the rest of the current pieces don't have those kind of glaring errors.  The new ones are being built with much more care and attention to detail.  It takes longer, especially since my dedicated building area isn't available right now, but I think I'll be much happier with the results.

I'm hoping, really hoping, to get some pictures posted up this week.  There's enough arena pieces to make things interesting and even without the snow the Crusaders will work well as models to show scale as well as help the composition be more dynamic.  The only problem is that I don't have floors made up so the pictures won't be as inclusive as I would like.  But those will be better than no pictures, I'm guessing.

Side note.  I'm rather trapped at home since we're down to one vehicle again.  Mr. Rastl was involved in what turned out to be a minor accident due to his excellent defensive driving skills.  Had he been less skilled, the accident would probably have been very, very bad.  So the truck is in the body shop having the entire passenger side fixed up, leaving me home while he takes the car.  I can work from home so that's not really an issue and since he tends to get home later I have even more time to work on this stuff.

Read and post comments | Send to a friend